| Author |
Message |
    
boter
New member
Username: boter
Post Number: 1
Registered: 05-2010
| | Posted on Sunday, May 09, 2010 - 03:02 pm: | 
|
Motor is seized from sitting
Need to order parts.
Looks like I need to know year of manuf.
I have read through threads-couldn't find info
Can anyone steer me.
Rear motor mount assembly: R M6 17928
Machined surface on block: M6*8708*
Cylinder head: E-58536-M-2
Sure would appreciate any ideas.
There is a tag on the block that shows it was rebuilt in 1957
THANKS |
drrot
Senior Member
Username: drrot
Post Number: 58
Registered: 09-2008
| | Posted on Monday, May 10, 2010 - 06:55 am: |
|
There is a list posted at http://www.finewoodboats.com/CHRYSLER1.htm |
boter
New member
Username: boter
Post Number: 2
Registered: 05-2010
| | Posted on Tuesday, May 11, 2010 - 02:18 pm: |
|
Jim
Thank you !
I had given up finding this info before trying this site and getting your answer.
I don't think that info is anywhere else on the internet.
Very much appreciated.
I see that my motor is near the end of the 1940-1948 production.
Does this mean that I can use a 1946-1948 car head gasket?
Thanks
Boter
PS I Now remember buying motor mounts for my Model K from you some years ago. |
drrot
Senior Member
Username: drrot
Post Number: 59
Registered: 09-2008
| | Posted on Tuesday, May 11, 2010 - 02:38 pm: |
|
You can use a car head gasket if it is copper or at least has copper liners in the water passages. |
boter
New member
Username: boter
Post Number: 3
Registered: 05-2010
| | Posted on Tuesday, May 11, 2010 - 09:10 pm: |
|
Jim
Thank you
Boter |
boter
Member
Username: boter
Post Number: 4
Registered: 05-2010
| | Posted on Sunday, August 22, 2010 - 08:53 am: |
|
Chrysler Ace
Dist. cap and rotor #'s to order ?
Can anyone help me?
Unable to find part #'s for dist cap and rotor.
#'s
-on engine block M6*8708
-on engine mount tag R M6 17928
-on dist 1115409
1GC 4724-1M
5B015119
Any guidance would be greatly appreciated
I do know from Finewood site that it is a mid 40's
Boter |
drrot
Senior Member
Username: drrot
Post Number: 62
Registered: 09-2008
| | Posted on Sunday, August 22, 2010 - 10:56 am: |
|
Part Autolite# ~~~ NAPA#
Cap IGC-1107S ~~~ AL63
Rotor IGS-1016B ~~~ AL62
Points IGP-3028VS ~~~ CS25
Cond. IGW-3139 ~~~ AL100 |
boter
Member
Username: boter
Post Number: 5
Registered: 05-2010
| | Posted on Sunday, August 22, 2010 - 06:21 pm: |
|
Wonderful!
Thank you Jim
I sometimes think it was not a good idea to pursue this motor but when I have support like this-its great.
Boter |
g3too
New member
Username: g3too
Post Number: 1
Registered: 09-2011
| | Posted on Sunday, September 25, 2011 - 11:02 pm: |
|
Boter,
You should do fine with that Ace. I ran one for 4 years in a 27' Cris Craft Super Deluxe when the original Crown was out for work. It was the hipo Special version, sodium valves and all. Reliable, adequate speed and pulled a skier. |
