Home | Classifieds | History | Technical | Links | Store | About Us | Email
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Heat Exchanger for PW 27 engine

Old Marine Engine » Palmer Engine Co » Heat Exchanger for PW 27 engine « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ken Pirko
Visitor
Posted on Friday, October 21, 2005 - 07:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I'm looking to find out if there is a heat exchange unit that was made to fit the PW 27 engine. I'm looking to install a fresh water PW 27 in my sailboat and use it in a salt water environment.
Top of pagePrevious messageNext messageBottom of page Link to this message

richardday
Senior Member
Username: richardday

Post Number: 470
Registered: 11-2003


Posted on Friday, October 21, 2005 - 09:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Ken try to find a used or new Sen-Dure Model 3BT-12-2P5. If you can find one for $300 if it isn't cracked or leaky grab it.
Top of pagePrevious messageNext messageBottom of page Link to this message

eddie
Senior Member
Username: eddie

Post Number: 80
Registered: 04-2003
Posted on Saturday, October 22, 2005 - 08:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Indigo Electronics makes an after market enclosed coolant system for Atomic4s. With a little adaptation I would think it might work for your engine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Krafft
Visitor
Posted on Monday, February 25, 2008 - 09:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I have a Sen-Dure marine heat exchanger. 4"+ Diam. X 20" +, not counting the end caps. 1" pipe thread at each end, centered, and 1" clamp nipples on each end of the "shell". Copper with bronze caps,flanges,ten brass bolts per end, and two mounting brackets. It appears to have been repaired in the past at a local radiator shop as there are tags on it. Three tubes appear plugged/patched with solder. Castings appear sound.
I filled the shell (no pressure/ends off) and found that one tube leaked. This is a vintage/old unit and was in the cellar of a house I purchased from the estate of the late boat owner.
Likely a spare as the gaskets were missing and bolts only hand tightened. It is not painted.
Does it have any value in the boat/engine restoration realm. I was considering plugging the leaking tube with epoxy and using it in a non-marine application but I am concerned about ruining it. I would prefer it went "home" to a boat if there is life left in it, or it would fill out someones "period restoration". Trying to avoid that dreaded "Road Show Remorse".
Any advice appreciated!

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page

Home | Classifieds | History | Technical | Links | Store | About Us | Email
&copy 2005 OldMarineEngine.com, P.O. Box 188, Forest Dale, VT 05745-0188 • Phone: 802-247-4864 • All rights reserved.
   Marine Engine Seloc Repair Manual Lookup Tool

marine gas engine repair and restoration