|
| Request help to identify a engine |
| Author |
Message |
    
amspicer
| | Posted on Saturday, September 07, 2002 - 09:33 pm: | 
|
Would appreciate any information that would help
identify a boat engine.
The engine is a inline 6cyl.orangey pink in color
with what looks like a transmission bolted to it,
attached to this is a Eaton outdrive. On the block is two sets of #. OH 31 and 8CIDE8015-A
Thanks,
Al Spicer |
andrew
| | Posted on Saturday, September 07, 2002 - 11:07 pm: |
|
Al,
When you say the numbers are "on the block" I would guess you mean "cast" into the block. Is there a nameplate attached to the engine that would have a builder, model number, serial number?
A lot of engines used Eaton outdrives, and the color of the engine doesn't mean much...
A picture might help... but the nameplate data would be best.
Regards,
Andrew |
James E. Harris
| | Posted on Sunday, January 26, 2003 - 05:25 pm: |
|
Al,
I'm sure you have id'd your engine by now. That second number you quoted is a Ford casting number, so your engine is a Ford.
Jim, the ENGINE ROOM, So. Portland, Maine |
Harold Hill
| | Posted on Wednesday, March 10, 2004 - 09:24 pm: |
|
I have a 1968 Larson,with a 302 Ford and a Eaton outdrive. My question is,does it have an impeller in the outdrive? Because it does have a secondary water pump on the motor.
Thanks
Harold |
david kilgore
Visitor
| | Posted on Monday, April 24, 2006 - 06:39 pm: |
|
Has anyone heard of a Hydrodone boat about a 68
model with a ford engine. Interceptor |
larry_from_maryland
Senior Member
Username: larry_from_maryland
Post Number: 152
Registered: 07-2003
| | Posted on Monday, April 24, 2006 - 07:29 pm: |
|
Interceptor is listed in the sparkplug book with several ford engines.It does not say hydrodone.Hydrodone is not listed seperatly.Hydrodyne is listed same as indmar. |
Anthony J Zgrodek Jr.
Visitor
| | Posted on Sunday, December 30, 2007 - 01:09 pm: |
|
I have a small one cylinder outboard that has no tname plate.It's a two cycle w/ egg shaped gas tank wraped around the magneto,pull rope wrapsaround mag & comes off after pulling rope. IT HAS A EISEMANN MAGNETO CORP, Brooklyn , NY w/ Model# 61-M & serial #47-D stamped on bottom of mag. The cast iron cylinder has the # 470-1881 stamped on it's side. The carborater has a cork float W/ Tillotson, Toleto, Ohio stamped on top of fuel bowl & #AJ16A stamped on the side. I need make , year, & horsepower of motor. Appreciate any help. |
bruce
Senior Member
Username: bruce
Post Number: 161
Registered: 07-2002
| | Posted on Sunday, December 30, 2007 - 05:44 pm: |
|
Anthony, Try searching on AOMCI.org |
Sean Rossi
Visitor
| | Posted on Monday, June 23, 2008 - 08:06 am: |
|
I have an old straight 6 Ford marine engine and need to find out the year and size to get a head gasket. The boat was built in 1973. Please help! |
Pat Dunne
Visitor
| | Posted on Sunday, April 26, 2009 - 09:04 am: |
|
I am looking to find out the value of twin 302 Falcon motors w/ eaton outdrives. They are on an old houseboat I am thinking of buying. They are in excellent condition, and low hours. E-mail me at [email protected] |
daveiis
Visitor
| | Posted on Saturday, January 23, 2010 - 07:57 pm: |
|
I'm looking for help to identify a 215hp v8 interceptor engine the data tag is in bad shape and no help the only numbers i can find are on the timing cover and are as follows interceptor no ce31r523125 any help would be appreciated i'm looking for gaskets valve cover intake timing cover |
phil austin
Visitor
| | Posted on Saturday, May 05, 2012 - 08:53 pm: |
|
I have a 1963 hydrodyne fish & ski under restoration. Need to identify the eaton outdrive.
I don't know what model it is. This is the info I have, ser.33480 ca 16R26. Saginaw Michigan.
There is a plate on ea side of the outdrive which has a emblem and says Interceptor 165. The engine is a Ford 260 Interceptor. Need to remove the outdrive and replace the bellows and possible seals? Any help in directions for removing and locating parts will be appericated.
thank you |
|
|
|
|
